OM POWER 2000A +
General description of the OM2000A+ automatic amplifier
The automatic linear amplifier OM2000A+ is designed for all short wave amateur bands from 1.8 to 29 MHz (including WARC – bands) + 50 MHz and all modes. It is equipped with a ceramic tetrode FU-728F.
Frequency coverage: | Amateur bands 1.8 – 29.7 MHz including WARC + 50 MHz |
Power output: | 2000+ W in SSB/CW on HF bands, 1500 W in RTTY 1500 W CW/SSB on 50 MHz |
Drive power: | 40 to 60 W for full output power |
Input impedance: | 50 Ohm VSWR < 1.5 : 1 |
Output amplification: | 17 dB |
Output impedance: | 50 Ohm unbalanced |
Maximum output SWR: | 3:1 |
SWR protection: | Automatic switching to STBY when reflected power is 350W or higher |
Intermodulation distortion: | better then -32 dBc |
Suppression of harmonics: | min -50 dBc (30–54 MHz better than -70dBc) |
Response speed of AUTO tune: | less than 0,5s within same BAND ,less than 3s if out of BAND |
Supported TRXs-CAT: | ICOM, ELECRAFT, KENWOOD, TEN-TEC ORION, YEASU, Icom transceive protocol using by microHAM devices – CI-V OUPUT, Flex Radios and Anan ( Apache Labs ) |
Tube: | FU-728F ceramic tetrode |
Cooling: | Centrifugal blower + axial blower |
Power supply: | Switchable 220,230,240V – 50/60 Hz or other primary voltages (for example 200V 50/60Hz for Japan) |
Transformers: | 1 toroidal transformer 3.0 kVA |
Protection circuits: | – SWR too high |
– Anode current too high | |
– Screen current too high | |
– Grid current too high | |
– Mistuning of power amplifier | |
– Temperature to high | |
– Soft start for fuse protection | |
– “switch –on blocking “ at opened amplifier | |
Indications: | 4.3″ colour touch screen display |
Features: | – Support automatic external Antenna switching |
– Memory for faults and warning, easy maintenance | |
– Automatic set-up anode current (BIAS) – no need to manual adjust after changing the tube | |
– Automatic set-up of blower speed according to temperature | |
– T/R System: QSK operation with built-in vacuum RF antenna relay | |
– Remote control – connector for LAN connection | |
– The smallest and lightest 2000 W automatic PA on the market | |
Mechanical parameters: | 390mm x 195mm x 370mm (width x height x depth) |
Weight: | 24 kg |
LAN Connection
Power amplifier is interfaced to LAN via XPORT made by Lantronix (type XP1001000-05R). More info can be found atwww.lantronix.com .
Default factory settings of XPORT are:
IP address: 192.168.1.211
Mask: 255.255.255.0
Gateway: 192.168.1.1
These are strictly default settings. You can modify any of these by going to XPORT web GUI via your web browser. We do not recommend changing any other parameters of the XPORT interface as loss of communication can be caused by doing so. There is no default user name or password. It is highly recommended to secure web interface with username and password.
For remote control and monitoring over LAN special software is needed. It is available free of charge; it can be downloaded from the following address:
http://www.om-power.com/download/HF_PA_Manager_v3.14-setup.exe.
Friedrichshafen 2016
Via EA4AK – Santos Rodrigues
NEWS @ HAM RADIO FHN 2016: OME POWER “OM2000A”
OM POWER is introducing a 2KW (2.3 KW max CW output) HF+50 MHz Amp to compete with ACOMs 2000A amplifier: The OM2000A. A totally truly automatic amplifier (self-tuning) with total remote control by software. Probably the first high power amp with an ethernet connector (TCPIP addreseable) on the back. VERY promising.
DIAMOND VX-30 Peter Waters G3OJV, explains why the Diamond VX-30 could be the ideal antenna for those new to ham radio who would like to operate on the VHF bands. The Diamond VX-30 is a 2m/70cm base station antenna with a frequency ran... Read more
Antenas